-
The 4005 Series
$79.59 – $673.08
Premium High Performance Carbide Drills
ECO | 2FL | 5xD | Solid | Inch & Metric
Every Cut Optimized. Self-centering drill point design means no pre-drilling operations are required
The ECO drill sizes are designed fto be combined with our PAC reamers as a perfect “1-2” combination
Learn More -
The 4105 Series
$90.86 – $999.79
Premium High Performance Carbide Drills
ECO | 2FL | 5xD | Coolant-through | Inch & Metric
Every Cut Optimized. Self-centering drill point design means no pre-drilling operations are required
The ECO drill sizes are designed to be combined with our PAC reamers as a perfect “1-2” combination
Coolant-through for increased MRR & tool life.
AdvaTech nano PVD coating increases wear resistance and lubricity over traditional drill coatings for ultimate drilling performance
Learn More -
The 4050 Series
$125.00 – $595.00
Premium High Performance Carbide Reamers
PAC | 1FL | Solid Carbide | Inch & Metric
Precise. Accurate. Concentric. The PAC reamer design is self-locating, thereby able to provide straightness and true position for dowel pin holes
Ideally coupled with the ECO drill series.
Diameter Tolerance: +0 /- .0002″
Learn More -
The 1010 Series
$29.72 – $173.90
Premium High Performance Carbide End Mills for Non-Ferrous Alloys
ART | 3FL | Chip Breaker | Radius | Alumigator
Alumigator Ramping Tool. Ideal for pocketing, profiling and ramping up to 45 degrees
When the absolute highest in Metal Removal Rates is the goal
Learn More -
The 1015 Series
$27.25 – $173.66
Premium High Performance Carbide End Mills for Non-Ferrous Alloys
AST | 3FL | Chip Breaker | Square & Radius | Alumigator
Alumigator Slotting & Roughing Tool. High speed slotting up to two times diameter
Staggered chip breakers for easy chip management and high quality surface finishes
Learn More -
The 1020 Series
$22.98 – $166.11Premium High Performance Carbide End Mills for Non-Ferrous Alloys
AFT | 3FL | Square & Radius | Alumigator
Alumigator Finishing Tool. Wiper flat for high quality floor finish
Designed to finish parts at roughing speeds and feeds
Learn More -
The 1025 Series
$15.49 – $431.30
Premium High Performance Carbide End Mills for Non-Ferrous Alloys
GWA3 | 3FL | Square & Radius | Alumigator
Wiper flat and circular land for high quality floor and wall finishes
Special radii available on request
Learn More -
The 1026 Series
$20.40 – $545.02Premium High Performance Carbide End Mills for Non-Ferrous Alloys
GWA3 | 3FL | Reduced Neck | Square 102 | Alumigator
Wiper flat and circular land for high quality floor and wall finishes
Special radii available on request
Learn More -
The 1027 Series
$20.09 – $462.30
Premium High Performance Carbide End Mills for Non-Ferrous Alloys
BNA3 | 3FL | Ball Nose | Alumigator
Circular land for exeptional wall finishes
Great for 3D surfacing non-ferrous alloys from Aluminum to Beryllium
Learn More -
The 1028 Series
$25.00 – $584.08
Premium High Performance Carbide End Mills for Non-Ferrous Alloys
BNA3 | 3FL | Reduced Neck | Ball Nose | Alumigator
Designed for High Speed Machining of Aluminum
Ramp, plunge, profile milling
Reduced neck for extended reach
Learn More -
The 1030 Series
$16.78 – $353.18
Premium High Performance Carbide End Mills for Ferrous Materials
HGW4 | 4FL | Square & Radius
Ideal for Tool Steels and Hard Alloys
Variable helix/unequal index design reduces vibration and enables higher metal removal rates
Special corner radii available upon request
Learn More -
The 1032 Series
$23.89 – $379.58Premium High Performance Carbide End Mills for Ferrous Materials
HGW4BN | 4FL | Ball Nose
Ideal for Tool Steels and Hard Alloys
Variable helix/variable index design reduces vibration and enables higher metal removal rates
Learn More -
The 1035 Series
$18.45 – $377.76
Premium High Performance Carbide End Mills for Ferrous Materials
HGW5 | 5FL | Square & Radius
Ideal for Tool Steels and Hard Alloys
Variable helix/variable index design reduces vibration and enables higher metal removal rates
Special corner radii available upon request
Learn More -
The 1040 Series
$22.38 – $418.80
Premium High Performance Carbide End Mills for Ferrous Materials
HGW7 | 7FL | Square & Radius
Ideal for Tool Steels and Hard Alloys
Variable helix/variable index design reduces vibration and enables higher metal removal rates
Special corner radii available upon request
Learn More -
The 1031 Series
$18.83 – $427.27
Premium High Performance Carbide End Mills for Ferrous Materials
SRF4 | 4FL | Square & Radius|
Ideal for Stainless and Hardened Steels
Variable helix/variable index design reduces vibration and enables higher metal removal rates
Special corner radii available upon request
Learn More -
The 1050 Series
$30.96 – $83.60Premium High Performance Carbide End Mills for Ferrous Materials
BND2 | DM2 | 2FL | Ball Nose | Die/Mold | MoldMaster
Ideal for Die/Mold applications in alloy and hardened steels
5-micron radius tolerance
Special modifications available upon request
Learn More -
The 2100 Series
$18.82 – $615.47Premium High Performance Carbide End Mills for Ferrous Materials
438 | 4FL | Square & Radius | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Ideally suited for gummy materials like Titanium and Stainless Steel
Learn More -
The 2105 Series
$22.23 – $403.80Premium High Performance Carbide End Mills for Ferrous Materials
438RN | 4FL | Reduced Neck | Square & Radius | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Reduced neck for extended reach
Learn More -
The 2115 Series
$27.79 – $377.45Premium High Performance Carbide End Mills for Ferrous Materials
438 | 4FL | Ball Nose | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Learn More -
The 2117 Series
$27.08 – $447.26
Premium High Performance Carbide End Mills for Ferrous Materials
438CB | 4FL | Radius | Chip Breaker | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Roughing nicks along the cutting edge act as chip breakers that produce smaller chips and reduce overall machine load. Ideal for roughing applications.
Learn More -
The 2205 Series
$20.45 – $727.05Premium High Performance Carbide End Mills for Ferrous Materials
538 | 5FL | Square & Radius | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Learn More -
The 2213 Series
$28.89 – $802.44Premium High Performance Carbide End Mills for Ferrous Materials
538RN | 5FL | Reduced Neck | Square & Radius | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Reduced neck for extended reach
Learn More -
The 2215 Series
$49.96 – $937.27Premium High Performance Carbide End Mills for Ferrous Materials
738 | 7FL | Square & Radius | PYSTL
Special edge preparation makes this an ideal tool for a broad spectrum of work materials
PYSTL features a 38 degree helix that reduces chatter and enables more aggressive and stable milling
Learn More -
The 2010 Series
$12.80 – $862.55
Premium Carbide End Mills for Non-Ferrous Alloys
250 | 2FL | Square & Radius
Learn More -
The 2015 Series
$19.98 – $439.50Premium Carbide End Mills for Non-Ferrous Alloys
250BN | 2FL | Ball Nose
Learn More -
The 2012 Series
$12.80 – $542.05Premium Carbide End Mills for Non-Ferrous Alloys
250 | 2FL | Reduced Neck | Square & Radius
Reduced neck for extended reach
Learn More -
The 2014 Series
$29.72 – $514.63Premium Carbide End Mills for Non-Ferrous Alloys
250BN | 2FL | Reduced Neck | Ball Nose
Reduced neck for extended reach
Learn More -
The 2030 Series
$12.80 – $862.55Premium Carbide End Mills for Non-Ferrous Alloys
350 | 3FL | Square & Radius
Learn More -
The 2031 Series
$19.18 – $426.71
Premium Carbide End Mills for Non-Ferrous Alloys
350WF | 3FL | Square | Wiper Flats
Integrated wiper flat design ideal for finishing operations
Floor finishing
Learn More -
The 2045 Series
$29.72 – $439.55Premium Carbide End Mills for Non-Ferrous Alloys
350BN | 3FL | Ball Nose
Learn More -
The 2032 Series
$23.78 – $542.05Premium Carbide End Mills for Non-Ferrous Alloys
350 | 3FL | Reduced Neck | Square & Radius
Reduced neck for extended reach
Learn More -
The 2047 Series
$29.72 – $514.63Premium Carbide End Mills for Non-Ferrous Alloys
350BN | 3FL | Reduced Neck | Ball Nose
Reduced neck for extended reach
Learn More -
The 2060 Series
$29.04 – $426.72Premium Carbide End Mills for Non-Ferrous Alloys
550 | 5FL | Square
Designed for High Speed Profiling of Aluminum
Learn More -
The 250 Series
$26.64 – $437.06Premium Carbide End Mills for Ferrous Materials
440V | 4FL | Square & Radius
Performance edge treatment
Features a variable helix and unequal index design that reduces chatter and enables more aggressive and stable milling
Learn More -
The 252 Series
$44.24 – $480.77Premium Carbide End Mills for Ferrous Materials
440VBN | 4FL | Ball Nose
Performance edge treatment
Features a variable helix design that reduces chatter and enables more aggressive and stable milling
Learn More -
The 255 Series
$29.30 – $480.77Premium Carbide End Mills for Ferrous Materials
540V | 4FL | Square & Radius
Performance edge treatment
Features a variable helix design that reduces chatter and enables more aggressive and stable milling
Learn More -
The 260 Series
$23.53 – $387.12Premium Carbide End Mills for Ferrous Materials
437 | 4FL | Square & Radius
Special edge preparation makes this an ideal tool for exotic materials
Features a variable index design with 37 degree helix that reduces chatter and enables more aggressive and stable milling
Learn More -
The 265 Series
$24.78 – $430.95Premium Carbide End Mills for Ferrous Materials
537 | 5FL | Square & Radius
Special edge preparation makes this an ideal tool for exotic materials
Features a variable index design with 38 degree helix that reduces chatter and enables more aggressive and stable milling
Learn More -
The 270 Series
$44.49 – $539.85
Premium Carbide End Mills for Ferrous Materials
815 | Multi Flute | Square & Radius
Ideal for hardened alloys and steels
Learn More -
The 280 Series
$91.18 – $576.76
Premium Carbide End Mill for Titanium
840 | Multi Flute | Square & Radius | Titanium
Ideal for Titanium and Titanium Alloys
Learn More -
The 285 Series
$112.54 – $380.66Premium Carbide End Mill for Titanium
840 | Multi Flute | Square & Radius | Reduced Neck | Titanium
Ideal for Titanium and Titanium Alloys
Reduced neck for extended reach
Learn More -
The 210 Series
$20.82 – $368.81
Premium Carbide End Mills for Semi-roughing & Finishing
335 | 3FL | Radius
Ideal for Semi-Roughing and Finishing
Learn More -
The 215 Series
$22.30 – $428.59Premium Carbide End Mills for Semi-Roughing & Finishing with a Ball Nose
335BN | 3FL | Ball Nose
Ideal for Semi-Roughing and Finishing
Learn More -
The 220 Series
$18.49 – $738.57Premium Carbide End Mills for Finishing
545 | 5FL | Square & Radius
Ideal tool for finishing
Learn More -
The 240 Series
$20.90 – $173.50
Premium Carbide Chamfer End Mills
S94 | 2FL | Chamfer Mill
Learn More -
The 241 Series
$27.31 – $173.50Premium Carbide Chamfer End Mills
S94 | 4FL | Chamfer Mill
Learn More -
The 243 Series
$12.92 – $504.15Premium Carbide Chamfer End Mills
CM2 | 2FL | 90 deg. | Chamfer + End Mill
Learn More -
The 244 Series
$15.38 – $554.94Premium Carbide Chamfer End Mills
CM4 | 4FL | 90 deg. | Chamfer + End Mill
Learn More -
P – Steel – Finishing P15
$0.00 – $149.47Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Semi Finishing P15
$75.71 – $139.76Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Finishing P25
$75.71 – $139.76Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Medium P25
$75.71 – $139.76Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Medium P35
$75.71 – $139.76Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Medium Roughing
$153.40 – $262.11Heavy Duty Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – Extreme Finishing
$161.12 – $238.76Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – M15
$166.94 – $246.53Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – Finishing M25
$75.71 – $262.06Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – M25
$75.71 – $149.47Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – Medium
$79.59 – $100.94Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
K – Cast Iron – K20
$75.71 – $262.06Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
N – Non-Ferrous – N15
$120.35 – $343.59Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
H – Hardened Steel – CERMET | Finishing
$75.71 – $168.88Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Roughing P15
$110.65 – $149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
M – Stainless Steel – Roughing M25
$102.88 – $149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – P25
$102.88 – $153.35Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Roughing P25
$0.00 – $149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Medium Roughing P35
$102.88 – $149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Heavy Steel P15
$91.24 – $155.29Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Heavy Steel P25
$110.65 – $514.41Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Heavy Steel P35
$97.06 – $149.47Positive Geometry Turning
All inserts sold in packs of 10.
Learn More -
S – Titanium – Titanium and HRSA S10
$102.88 – $149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Heavy Steel – P25
$149.47 – $262.06Heavy Duty Turning
All inserts sold in packs of 10.
Learn More -
P – Steel – Roughing P35
$149.47Negative Geometry Turning
All inserts sold in packs of 10.
Learn More -
GWS Armory Magazine Well Rougher
$214.50The Magazine Well Rougher is our 3 flute GW Armory ART series end mill for roughing the magazine well on an AR-15 lower reciever. The tool can ramp in at 45 degrees, then finishes the side walls, leaving just the corners for our mag-well broach.
Magazine Well Rougher3 Fl, 37° HLX | Ø.625 IN. | 1.625 IN. LOC | .625 IN. SHK | 5.00 IN. OAL |2.625 REACH | CARBIDE END MILL
Length: Long
Learn More
End Type: R.02 Corner Radius
Coating: NONE
Length of Cut: 1.625
Cutting Diameter: 0.625 -
GWS Armory Trigger Pocket Rougher
$82.00The Trigger Pocket Rougher is our 3 flute GW Armory cutter for roughing the trigger pocket on an AR-15/10 lower reciever.
Trigger Pocket Rougher3 Fl, 37° HLX | Ø.375 IN. | .500 IN. LOC | .500 IN. SHK | 1.25 IN. REACH | 3.0 IN. OAL | CARBIDE END MILL
Length: Standard
Learn More
End Type: R.015 Corner Radius
Coating: NONE
Length of Cut: 0.5
Cutting Diameter: 0.375 -
GWS Armory Picatinny Rail Profile Cutter
$426.71The Picatinny Rail Cutter is our 8 flute GW Armory form tool for milling the picatinny rail on the AR-15 upper reciever and heat sheild.
Picatinny Rail Profile Cutter8 Fl, Straight | Ø.940 | .5 IN. SHK | 3.0 IN. OAL | CARBIDE FORM TOOL
Length: Standard
Learn More
End Type: R.02 Corner Radius
Coating: NONE
Length of Cut: 0.424
Cutting Diameter: 0.94 -
GWS Armory Ejection Door Keyway
$577.77The Ejection Door Keyway cutter is our 10 flute GW Armory cutter for plunge milling the .625″ radius between the ejection port cover hinge bosses on the AR-15 upper reciever.
Ejection Door Keyway10 Fl, 20 HLX | Ø1.250 | .625 IN. SHK | 6.0 IN. OAL | CARBIDE KEYWAY CUTTER
Length: Standard
Learn More
End Type: R.008 Corner Radius
Coating: NONE
Length of Cut: 0.26
Cutting Diameter: 1.25 -
GWS Armory Charging Handle Broach
$415.84The Charging Handle Broach is our GW Armory cutter for broaching the .015″ radius at the back of the charging handle slot on the AR-15 upper reciever.
.420 WIDE X .610 HIGH | .750 IN. SHK | 4.0 IN. OAL | CARBIDE BROACH
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.28
Cutting Diameter: -
GWS Armory Charging Handle Keyway
$311.11The Charging Handle Keyway Cutter is our GW Armory cutter for finishing the charging handle slot on the AR-15 upper reciever.
Charging Handle Keyway6 Fl, 37 HLX | Ø1.250 | .625 IN. SHK | 3.5 IN. OAL | CARBIDE KEYWAY CUTTER
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.127
Cutting Diameter: 0.507 -
GWS Armory Charging Handle Lock Position Form
$57.87The Charging Handle Lock Position Form Tool is our 3 flute GW Armory end mill for milling the slot for the T-handle at the rear of the AR-15 upper reciever.
Charging Handle Lock Position Form3 Fl, 37° HLX | Ø.300 IN. | .75 IN. LOC | .3125 IN. SHK | 2.00 IN. OAL |.850 REACH |.08 X 45° CHAMFER | CARBIDE END MILL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.75
Cutting Diameter: 0.3 -
GWS Armory Gas Tube Counter Bore Drill
$276.44The Gas Tube Counter Bore Drill is our GW Armory step drill for drilling the gas tube hole and c’bore in one shot on the AR-15 upper reciever.
Gas Tube Counter Bore Drill2 Fl, 30 HLX | Ø.1845 | 118 DEG. INCL. POINT | .375 IN. SHK |9.0 IN. OAL | CARBIDE DRILL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.9
Cutting Diameter: 0.1845 -
GWS Armory Charging Handle Clearance Endmill
$53.45The Charging Handle Clearance End Mill is our 6 flute GW Armory GWA3 series end mill for milling the clearance groove for the charging handle on an AR-15 upper receiver.
Charging Handle Clearance Endmill3 Fl, 37° HLX | Ø.420 IN. | .25 IN. LOC | .4375 IN. SHK | 3.00 IN. OAL |.630 REACH | CARBIDE END MILL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.25
Cutting Diameter: 0.42 -
GWS Armory Forward Assist Combo Form Drill
$412.93The Forward Assist Combo Drill is our 2 flute GW Armory step drill for drilling and counter boring the forward assist hole and c’bore in an AR-15 upper reciever.
Forward Assist Combo Form Drill2 Fl, 40 HLX | Ø.315 | 120 DEG. INCL. POINT | .625 IN. SHK |5.0 IN. OAL | CARBIDE DRILL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 2.375
Cutting Diameter: 0.315 -
GWS Armory Detent Groove Cutter for Ejector Door
$188.56The Detent Groove Cutter is our 4 flute GW Armory radius form cutter for milling the detent groove for the ejector door in an AR-15 upper reicever.
Detent Groove Cutter for Ejector Door4 Fl, Straight | Ø.400 | .500 IN. SHK | 3.0 IN. OAL | CARBIDE RADIUS KEYWAY CUTTER
Length: Standard
Learn More
End Type: R.0625 Corner Radius
Coating: NONE
Length of Cut: 0.125
Cutting Diameter: 0.4 -
GWS Armory Broach For Magazine Well Corners
$737.69The Magazine Well Broach is our GW Armory cutter for magazine well on an AR-15 lower reciever.
Broach For Magazine Well Corners.470 WIDE X .630 HIGH | .750 IN. SHK | 6.0 IN. OAL | CARBIDE BROACH
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.28
Cutting Diameter: -
GWS Armory Locking Lug Form Tool
$603.93The Locking Lug Form Tool is our 6 flute form cutter for cutting the grooves in the AR-15 bolt to create the locking lugs.
Locking Lug FT6 Fl, HEL | Ø.950 | 1. IN. SHK | 4.0 IN. OAL |nACo COATED | CARBIDE FORM TOOL
Length: Standard
Learn More
End Type: Square End
Coating: nACo
Length of Cut: 0.2188
Cutting Diameter: 0.95 -
GWS Armory Firing Pin Reamer
$272.62The Firing Pin Reamer is our 4 flute GW Armory cutter for finishing the large diameter, angle, and radius leading into the small through hole on the AR-15 bolt. Use this tool after both diameters are roughed to produce the highest quality ID finish.
Firing Pin Reamer4 Fl, 5 HLX | Ø.1575 | .1875 IN. SHK |4.0 IN. OAL | CARBIDE REAMER
Length: Standard
Learn More
End Type: Square End
Coating: nACo
Length of Cut: 1
Cutting Diameter: 0.0549 -
GWS Armory Bearing Surface U’cut Form Tool
$884.51The Bearing Surface Undercut Form Tool is our 4 flute GW Armory cutter for milling the clearance grooves in the bolt carrier
Bearing Surface U’cut Form Tool6 Fl, 10 HEL | Ø1.25 | 1.25 IN. SHK | 4.0 IN. OAL | ALTiN COATED | CARBIDE FORM TOOL
Length: Standard
Learn More
End Type: Square End
Coating: AlTiN
Length of Cut: 0.75
Cutting Diameter: 1.25 -
GWS Armory Firing Pin Hole & Form
$312.06The Firing Pin Form Drill is our 2 flute GW Armory drill for finishing the large diameter, angle, radius, and small diameter to size. Use this form drill after a jobber of your choice.
Firing Pin Hole & FormCoolant through
4mm Shank
Step Drill
.068 DIA
2 Flutes
5″ Overall Length
3″ Length of Cut2 Fl, 30 HLX | Ø.068 | 118 DEG. INCL. POINT | .1575 IN. SHK |5.0 IN. OAL | CARBIDE STEP DRILL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 3
Cutting Diameter: 0.068 -
GWS Armory Rail Groove Rougher
$35.14The Rail Groove Rougher is our 3 flute GW Armory series for roughing the slots on a picatiny rail.
Rail Groove Rougher3 Fl, 30° HLX | Ø.2 IN. | .1234 IN. LOC | .250 IN. SHK | 2.00 IN. OAL | CARBIDE FORM TOOL
Length: Standard
Learn More
End Type: Square End
Coating: NONE
Length of Cut: 0.25
Cutting Diameter: 0.2 -
GWS Armory Rail Groove Finisher With Debur
$63.00The Rail Groove Finisher With Debur is our 3 flute GW Armory form tool for finishing the slots on a picatiny rail to size and breaking the edge at the top of the rail.
Rail Groove Finisher With Debur3 Fl, 37° HLX | Ø.2 IN. | .25 IN. LOC | .250 IN. SHK | 2.00 IN. OAL | CARBIDE END MILL
Length: Standard
Learn More
End Type: R.005 Corner Radius
Coating: NONE
Length of Cut: 0.1234
Cutting Diameter: 0.2125 -
GWS Armory Rail Groove Finisher
$39.40The Rail Groove Finisher is our 3 flute GW Armory form tool for finishing the slots on a picatiny rail to size.
Rail Groove Finisher3 Fl, 37° HLX | Ø.2125 IN. | .200 IN. LOC | .250 IN. SHK | 2.50 IN. OAL | ZrN COATED |CARBIDE END MILL
Length: Standard
Learn More
End Type: Square End
Coating: ZrN
Length of Cut: 0.2
Cutting Diameter: 0.2125
